Search:

Type: Posts; User: WMF

Page 1 of 8 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    36
    Views
    4,508

    I use electric level switch and motorized ball...

    I use electric level switch and motorized ball valve and pump directly into steamaway. I have a panel with flowmeter and bypass valve so I can adjust flow to a little less than steamaway is using and...
  2. Replies
    36
    Views
    4,508

    22383 When you look into your concentrate tank...

    22383
    When you look into your concentrate tank and see this you have no guilt about waiting a few days to boil. This was 14 brix about 29 degrees and is just slushy on top with the agitator always...
  3. Replies
    36
    Views
    4,508

    I have been experimenting with running chilled...

    I have been experimenting with running chilled glycol through the refrigerant jackets on a 2000 gallon Mueller for the last two years with good results.
    This still requires a glycol chiller which...
  4. Replies
    36
    Views
    4,508

    I have looked at the brazed heat exchangers and...

    I have looked at the brazed heat exchangers and have always been concerned with the inability to clean them. From my research the shell and tube type seem to be the best sanitary style but food grade...
  5. Replies
    36
    Views
    4,508

    What type of chiller did the dairy guy recommend?...

    What type of chiller did the dairy guy recommend? I know it is common for dairies to use a well water powered plate cooler to lower the temp into the 60 degree range and then they use refrigeration...
  6. Replies
    11
    Views
    2,260

    Just keep in mind with a two line setup you will...

    Just keep in mind with a two line setup you will be constantly filtering your whole tank of fuel and if your tank has crud settled out in it your fuel filter may need changing more frequently.
    I...
  7. Thread: Membrane snot

    by WMF
    Replies
    9
    Views
    1,019

    Trust me, no fluid exudes through the fiberglass...

    Trust me, no fluid exudes through the fiberglass outer wrap of a membrane. All fluid goes in one end and comes out the other minus the permeate.
    If a membrane is in a standard housing and there is a...
  8. Thread: Membrane snot

    by WMF
    Replies
    9
    Views
    1,019

    The real problem is the space between the...

    The real problem is the space between the membrane and wall of pressure vessel is a dead space if brine seal is in place and sealing.
    Commercial units with real recirculation use the gap between the...
  9. Thread: oil gun problem

    by WMF
    Replies
    10
    Views
    952

    I would start by getting wiring diagram of the...

    I would start by getting wiring diagram of the primary control that is on the burner. There are several different ones used on a 701. Find out what exactly is "burned up" on the controllers.
    If the...
  10. Replies
    244
    Views
    148,133

    If you don't have one already keep your eye out...

    If you don't have one already keep your eye out for a Genuine made in USA Beverly shear. They make cutting metal so easy and they will last forever if cared for.
  11. Replies
    244
    Views
    148,133

    Another great old USA made tool. The crimping...

    Another great old USA made tool. The crimping dies should go on the shaft before the beading dies so it makes a shoulder after the crimp. You can use just the crimping dies or just the beading dies...
  12. Replies
    244
    Views
    148,133

    Looks great, that arch will last a lifetime if...

    Looks great, that arch will last a lifetime if kept dry.
    I think the brake you may have been thinking yours was is a Cornice truss brake made in Buffalo. They made them out of a combination of wood...
  13. Replies
    244
    Views
    148,133

    Looks like a Chicago, I have an old Chicago 818...

    Looks like a Chicago, I have an old Chicago 818 and the legs and castings look exactly the same. The Chicago's have a round brass tag with a single rivet in the center located on the right side...
  14. Replies
    244
    Views
    148,133

    Sweet! Is that a 1016 ? Looks like it found a...

    Sweet! Is that a 1016 ? Looks like it found a good home.
  15. Replies
    4
    Views
    609

    Changed bearings on one a few years ago. The...

    Changed bearings on one a few years ago.
    The impeller unsrews from shaft then you can remove motor.
    Make sure to index everything. I would draw a witness line down one side of pump/motor with paint...
  16. Thread: Releaser problems

    by WMF
    Replies
    18
    Views
    3,318

    I drilled and tapped a 6-32 screw into the thick...

    I drilled and tapped a 6-32 screw into the thick clear plastic bar that the bushings go through. Used a screw just long enough to pin bushing,
    do this at your own risk as these plastic parts are not...
  17. Thread: Releaser problems

    by WMF
    Replies
    18
    Views
    3,318

    I have two double vertical Bernards. Both have...

    I have two double vertical Bernards. Both have had issues of which you speak and the cause was the white machined bushings in the clear
    cover that the float rods run through.
    The bushings are press...
  18. Replies
    3
    Views
    781

    My Sihi 3708 is stuck every year even though it...

    My Sihi 3708 is stuck every year even though it is stored with glycol. I panicked the first time it happened then sat back and analyzed why it is stuck.
    The rotors and housings are close tolerance...
  19. What size burner tube does your 301 have? This...

    What size burner tube does your 301 have? This burner can be ordered with either a 3.25" tube for 3 to 6 gph firing rate or 3.5" burner tube for 4 to 7 gph.
    Your firing rate is right at the cutoff...
  20. Thread: Squirrel Chews

    by WMF
    Replies
    7
    Views
    1,937

    Its chipmunks and flying squirrels. The woods I...

    Its chipmunks and flying squirrels. The woods I have down the road from you is always full of this damage and also the coyote's show up and chop clean a few dozen of the steepest most inaccessible...
  21. Thread: Seprotech Parts

    by WMF
    Replies
    12
    Views
    2,310

    Wiam's Seprotech is the old school with...

    Wiam's Seprotech is the old school with fiberglass vessels and a single 3hp forged stainless recirc pump plumbed in series with the vessels via 1.5 inch copper pipe.
    The seal is the same style as in...
  22. Thread: Seprotech Parts

    by WMF
    Replies
    12
    Views
    2,310

    The shaft seal for that 3hp recirc pump is...

    The shaft seal for that 3hp recirc pump is available but may not be in stock by any maple dealers any more. Leader used to have them in stock as the same seal was used in the old fiberglass vessel...
  23. Replies
    18
    Views
    3,765

    If you double the papers you will not blow a...

    If you double the papers you will not blow a paper and can run the press to 60 psi or beyond. The extra cost is negligable compared to tearing down a press full of syrup and using another set of...
  24. Thread: Wood ID Help

    by WMF
    Replies
    22
    Views
    8,192

    Looks like Crab Apple or some variant of it. Is...

    Looks like Crab Apple or some variant of it. Is it heavy and dense?
  25. Replies
    14
    Views
    6,203

    Looks like Hickory

    Looks like Hickory
Results 1 to 25 of 184
Page 1 of 8 1 2 3 4