Search:

Type: Posts; User: lmathews

Page 1 of 11 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    5
    Views
    3,796

    www.farmertec.com Rebuilt many saws using...

    www.farmertec.com
    Rebuilt many saws using parts from this supplier.
  2. Thread: Maple sugar

    by lmathews
    Replies
    3
    Views
    4,535

    Thank you.I attended a seminar and that is where...

    Thank you.I attended a seminar and that is where the info came from. However Steve did not go in to much detail about it that day. I will reach out to him.
    Thanks
  3. Thread: Maple sugar

    by lmathews
    Replies
    3
    Views
    4,535

    Maple sugar

    Anyone have any information on using a pressure cooker for heating up syrup to the proper temp for cream or sugar?
    Thanks Lee
  4. Replies
    10
    Views
    952

    Problem solved! great to know it was a factory...

    Problem solved! great to know it was a factory problem. It was in the wiring harness were the technicians put in a poor splice job and it melted the wires together.
    Thank you all.
  5. Replies
    10
    Views
    952

    I am not sure how to attach photos.

    I am not sure how to attach photos.
  6. Replies
    10
    Views
    952

    There are separate contactors for motor and air...

    There are separate contactors for motor and air damper control. When primary is burned up it is the circuit that turns on the oil solenoids.
  7. Replies
    10
    Views
    952

    Picked motor up today,no problems with it. ...

    Picked motor up today,no problems with it.

    I have checked all connections and changed breaker. Seems to happen when high fire is involved. High fire timer blower damper contactor problem?
  8. Replies
    10
    Views
    952

    oil gun problem

    Hello,
    I have a carlin 701crd oil gun 4 years old. I started having an issue halfway through this past season. At no specific time it would happen.
    I would be boiling for maybe 2 hours and...
  9. Replies
    6
    Views
    835

    If you research current standards the goal has...

    If you research current standards the goal has been changed to 3 taps per lateral run for the efficiency of high vac transfer to the tap. However there is always a couple of runs with 4 or 5. I am...
  10. Replies
    10
    Views
    24,102

    If I may ask what is this ?

    If I may ask what is this ?
  11. Thread: Hong Kong

    by lmathews
    Replies
    1
    Views
    1,209

    Hong Kong

    Anyone getting requests for an order for products for a store in Hong Kong?

    Clearwater Bay Stores
  12. Replies
    4
    Views
    1,401

    Association member increase

    I received my email for nys maple association renewal and noticed it is up $15.00 what is the reason?
    Thanks
  13. Replies
    207
    Views
    70,635

    Bascom via phone last week stated $1.90...

    Bascom via phone last week stated
    $1.90 for dark robust.
    $1.75 extra dark strong.
    $.90-$1.10 off,ropy,non filtered.
    Hope this helps.
  14. Replies
    0
    Views
    826

    D & G fittings

    Can anyone tell me a part number or what the pan connector fitting that D & G uses is called?I tried to load a picture.
    Thanks16283
  15. Replies
    1
    Views
    1,008

    No one out there?

    No one out there?
  16. Replies
    1
    Views
    1,008

    D&G oil fire raised flue arch

    If anyone has a Dominion Grimm oil fire raised flue evaporator could you please send me some pictures of the inside of your arch?I would like some pics of the fire box and under the flue pan ramp...
  17. Replies
    173
    Views
    72,003

    Any one have current prices?

    Any one have current prices?
  18. Unless you have a set of torches.When I worked...

    Unless you have a set of torches.When I worked construction in the cheese plants we would have to demo old steel shell silos and would use a small orifice torch tip.Cut right where the two metals...
  19. Replies
    5
    Views
    2,397

    I would recommend speed 4 to start and if it...

    I would recommend speed 4 to start and if it starts to bog down turn it to 6 I have even had to turn mine up to 10.If you are doing batches 1st one is usually 30 min to finish.Next ones are a lot...
  20. Replies
    5
    Views
    2,397

    I think it would be an issue with not cooking it...

    I think it would be an issue with not cooking it long enough.Most recommendations are 22-24 degrees above the boiling point. Also it could be you stopped stirring it to soon.
  21. Replies
    9
    Views
    5,453

    From experience it sounds like basswood.I burn...

    From experience it sounds like basswood.I burn all popple and basswood
  22. Replies
    181
    Views
    80,607

    Is there contact info for Highland?

    Is there contact info for Highland?
  23. Replies
    422
    Views
    179,801

    So much for a good run.Gotta love the wind.

    So much for a good run.Gotta love the wind.
  24. Thread: Caps

    by lmathews
    Replies
    6
    Views
    3,023

    If there is no seal I will guarantee that you...

    If there is no seal I will guarantee that you will have mold show on the top of a portion as they sit.I had this problem as well with caps like you are describing with a 25% fail rate.
  25. Thread: Transfer hose

    by lmathews
    Replies
    5
    Views
    2,083

    Tractor supply

    Tractor supply
Results 1 to 25 of 252
Page 1 of 11 1 2 3 4