+ Reply to Thread
Results 1 to 4 of 4

Thread: 500 Taps - mostly gravity....but here's my problem - what is the best plan of attack?

  1. #1
    Join Date
    Sep 2011
    Location
    Beautiful Napanee, Ontario, Canada (BNOC)
    Posts
    13

    Default 500 Taps - mostly gravity....but here's my problem - what is the best plan of attack?

    First post...

    So I have 500 taps that I am going to put on 5/16 tubing and run into two 1" mainlines. All flows downhill and will gravity feed into a 800 gallon tank. From there, I need to move it from the tank to the sugar shack (SS). Run is about 75' and is pretty much level. Sugar Shack is 20x30 and 10x20 is heated and has electricity.

    How do I get the 800 gallons from the tank into the SS, and then pumped into an elevated tank that is going to gravity feed the evaporator.

    What's the best bang for buck - I could do vacuum, releaser into elevated tank......I could do RO, but that is probably a few years off....

    Thanks!
    Kenn
    --------
    2016 - 300 taps (50 on gravity fed pipeline)
    2015 - 250 taps, RTV to collect.
    2012 - plan on 300 taps as we are cutting new trails into the maple trees...
    2011 - 175 taps on buckets. ATV to collect and stored in 500 gal stainless steel tank. 104 litres of syrup produced.
    2010 - revamped original sugar shack (new concrete floor, windows and rescrewed steel on roof). 2x6 Patrick Phaneuf evaporator.
    2009 - purchased 30 acres of bush - some of it with maple trees

  2. #2
    Join Date
    Dec 2006
    Location
    NE PA (Pocono's)
    Posts
    1,426

    Default

    Vacuum would be the way go go otherwise you can consider this alternative . https://www.waterpumpsdirect.com/Hon...ump/p6298.html
    CDL 2x8
    Around 4000 taps
    Polaris ATVs, Ski Doo snowmobiles to get around
    Atlas Copco pumps
    Lapierre two post RO




    http://s272.photobucket.com/albums/j...Sugar%20shack/

  3. #3
    Join Date
    Nov 2010
    Location
    Bakersfield, VT
    Posts
    241

    Default

    I used to us a plastic sump pump with no float. that way I could plug in when I needed more sap and unplug when the head tank was full. Just had to watch and not forget and run it over. Still us the pump to move water or sap around. They move liquid pretty quick and no gas motor to listen to or keep going.
    54 Acres bought in Sept 2010, hope for a lot of fun
    Kabota 3400 w/ bucket
    couple Husky chainsaws and a couple of Stihl
    Big dream
    2011 = 106 on gravity tubing, 100 bucket
    2012 =700 vaccuum 100 gravity 80 bucket's
    30" x 12' Vortex with Leader Revolution Max Raised pans
    2013 = 1200 vac, 200 gravity, 5 buckets, buying from 300 buckets, 500 vac
    Springtech RO 600 Deluxe
    2015= 1800 all vac @ home, buying sap from 1200.
    2017= 2200 all on vac. no longer buying sap

  4. #4
    Join Date
    Jan 2006
    Location
    Oneida NY
    Posts
    11,675

    Default

    A sump pump can be risky. The issue with them is that they are sealed in oil, if the seal fails the sap is ruined.
    Lots of pumps are suitable for pumping sap, but they need to be dedicated pumps. An aluminum housed water pump does fine for lots of producers. When I need to move sap without using my RO, I use a Honda WX15 (1.5" pump), a Honda WX10 is good too. However there are lots of lower cost pumps that do fine. Another option is to use a diaphragm pump, either AC or DC. That can give you some vacuum and it can both pull sap to it and push sap from it. They will work best if the diaphragm is kept wet. To do that use a 3/16 or a 5/16 line from the destination tank back to the pump inlet. A valve can help adjust the flow, only a small portion of the available flow in either size needs flow back thru the diaphragm.
    Most using diaphragm pumps use 12V pumps, on a good 12V deep cycle battery they will run 24 hrs. For that have 2 batteries, one on the pump while the second is on the charger. The only diaphragm pump I've used is a 120V one, I use it to pump water thru my tankless water heater.
    If I read correctly, you will need to pump about 75', fairly level ground, then up to your elevated head tank. A 120 V type would do fine for that, just use the right gauge extension cord. Keep the pump where you were going to put the tank, but place the tank at the sugarhouse. Then make a small insulated enclosure for the pump, maybe even with a small electric heater. This type of pump does not do well with ice going into the diaphragm. There at least 2 methods help. One could be a 1 gal or larger container on the suction side with the inlet high and the outlet to the pump inlet low. The ice will float and the liquid sap will be pulled from under it. Another method can be an inline screen to stop the ice. If you also use a heater, use a low temp thermostat. Do not heat it to over 40-42F, the sap keeps best the colder it is.
    Dave Klish, I recently bought a 2x6 wood fired evaporator from A&A Sheet Metal which I will be converting to oil fired
    Now have solar, 2x6 finish pan, 5 bank 7x7 filter press, large water jacketed bottler, and tankless water heater.
    Recently bought another Gingerich RO, this one was a 125, but a second membrane was added thus is a 250, like I had.
    After running a 2x3, a 2x6, 3x8 tapping from 79 taps up to 1320 all woodfired, now I'm going to a 2x6 oil fired and a 200-425 taps.

+ Reply to Thread

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts