+ Reply to Thread
Results 1 to 9 of 9

Thread: holes drilled horizontally

  1. #1
    Join Date
    Feb 2014
    Location
    finger lakes NY
    Posts
    51

    Default holes drilled horizontally

    Sent my son out to tap one section on his own, he drilled and tapped all of the holes almost perfectly horizontal instead of a slight downward angle. Will this have a poor effect on the amount of sap that the tree will give up?
    about 30 taps 5 gallon pails on tubing
    boiling on propane
    high elevation
    goal is 6 gallons of tasty syrup for family and friends

  2. #2
    Join Date
    Mar 2012
    Location
    Bristol, New York
    Posts
    23

    Default

    Should be fine, where are you ?? Im in Bristol, tapping this weekend, approx. 50 taps.

  3. #3
    Join Date
    Mar 2010
    Location
    Suamico, WI
    Posts
    1,176

    Default

    That's good.....he knows the correct way to tap. All tap holes should be drilled at a 90. There is NO need for a upward
    Angle as that will only give a oblonged hole that can leak. When a tree is running it is under upwards of 10 psi at the tap hole, believe me the sap will come out
    custom made 2x7 intensofire
    With SL pans
    250 deer run
    300 3/16 (new 2016)
    500 sacks around the neighborhood

  4. #4
    Join Date
    Feb 2014
    Location
    finger lakes NY
    Posts
    51

    Default

    we are in Steuben County, still no sap but it should be coming soon!
    about 30 taps 5 gallon pails on tubing
    boiling on propane
    high elevation
    goal is 6 gallons of tasty syrup for family and friends

  5. #5
    Join Date
    Oct 2011
    Location
    Weare, NH
    Posts
    190

    Default

    It depends whether you are on vac or not. It's more important to drill holes 90 degrees to the surface on vac so they stay round and are less likely to leak. With gravity I still think you want that downward slope and an oval hole doesn't matter as much.
    Sugarbush in Tunbridge VT.
    1080 taps for 2014 (made 506 gallons)
    2hp liquid ring vac
    3x10 small bros w/preheater, blower and new airtight front = 140 gph
    Sap Brother Eco-50 RO w/4 xle 4040s and 360gph pump

  6. #6
    Join Date
    Jan 2006
    Location
    Oneida NY
    Posts
    11,675

    Default

    Drilled straight is best, but as long as you go in and back out without any wobble I fail to see how you get an oval hole. It may look oval looking from an angle different than the bit went in, but a bit only drills a round hole if the angle remains constant, and a hole drilled at 90 degrees to the surface only remains round the same way, do not wobble the bit.
    Dave Klish, I recently bought a 2x6 wood fired evaporator from A&A Sheet Metal which I will be converting to oil fired
    Now have solar, 2x6 finish pan, 5 bank 7x7 filter press, large water jacketed bottler, and tankless water heater.
    Recently bought another Gingerich RO, this one was a 125, but a second membrane was added thus is a 250, like I had.
    After running a 2x3, a 2x6, 3x8 tapping from 79 taps up to 1320 all woodfired, now I'm going to a 2x6 oil fired and a 200-425 taps.

  7. #7
    Join Date
    Mar 2015
    Location
    Monkton, Vermont
    Posts
    2

    Default

    Am I missing something here? The hole itself is still round, even if you drill it at an angle. It's just the intersection of the hole with the surface of the tree that is oval. I'm brand new to this, so not trying to argue, just trying to understand. The only way I can see it mattering is if what's important for a leak-free fit is how the part of the tap that stays outside the tree "matches" the tree surface (i.e. if there is some sort of collar on the tap). I thought the important thing was how the body of the tap fit into the hole, which is not affected by whether the hole is drilled at a slight angle.

  8. #8
    Join Date
    Mar 2008
    Location
    Lake County Ohio
    Posts
    1,634

    Default

    John Mc. You are not missing anything - Dave is correct; a drill bit will produce a round hole no matter the angle of penetration. Providing the body of the tap is the same dia (not tapered) where it's in contact with the outer surface - whether table top or tree - you will have a tight fit.

    Woodworkers often install wood plugs in furniture that are drilled at an angle, it's called pocket hole joinery. Then end result is an often attractive oblong shaped plug in a contrasting - darker or lighter - wood. Sure hope the sap starts running soon...the natives are getting restless.

    pocket joinery.jpg
    John Allin

    14x18 Hemlock Timber Frame Sugar House 2009
    Leader 2x6 w/Patriot Raised Flue Pan 2009
    Leader Steam Hood 2014 - Clear Filter Press 2015
    Leader Revolution Pan and SS Pre-Heater 2016
    CDL Hobby RO & Air Tech L25 Hi Vac Pump 2019
    06' Gator HPX to collect wood & sap
    14' Ski-Doo Tundra for winter work in the woods
    Great Family 3 grown kids+spouses and 7 grand kids who like the woods
    7th Gen Born in Canada - Raised in Chardon Ohio - Maple Capital of the World..<grin>.

  9. #9
    Join Date
    Mar 2008
    Location
    Central Ohio
    Posts
    318

    Default

    There is a potential problem with a bucket spile drilled horizontally: the drips may not drop off at the end. They may run back to the wall of the bucket and drip out of the hole in the bucket. This is a function of the spile design. Some have a better "drip edge" than others. A down angle can prevent this.
    Central Ohio
    Leader WSE 2x6
    Old metal corn crib converted to "The Shack"
    Smoky Lake 6 gallon water jacket canner
    Daryl 5" filter press with air pump
    Deer Run 125 RO

    2023: 140 taps, buckets, 32 gallons
    2019: 100 taps, buckets, 45 gallons
    2018: 100 taps, buckets, 31 gallons
    2017: 100 taps, buckets, 15 gallons
    2015: 100 taps, buckets, 34 gallons
    2014: 100 taps, buckets, 30 gallons
    2013: 100 taps, buckets, 52 gallons

+ Reply to Thread

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts