Good morning. I just installed an 8" Selkirk sure temp double wall pipe through my sap house roof and want to go back to single wall because I have 15' of it. Is there an adapter to go from the male sure temp back to single wall stainless?
Stack adapter
Good morning. I just installed an 8" Selkirk sure temp double wall pipe through my sap house roof and want to go back to single wall because I have 15' of it. Is there an adapter to go from the male sure temp back to single wall stainless?
2014 6 Taps Block Arch and momas canning pot, 3 gallons YIKES
2019 100 taps and a new adventure with a home built arch.
2020 90 taps, my wife and I and a Bucket RO...
2021 112 taps and a modified Bucket RO.
2022 120 taps, modified Bucket RO a Wife, Son and Springer
This might work? Jay
Selkirk® 8DSP-CPA - DSP Chimney Pipe Adapter
I know they come in steel or Stainless
Zucker Lager
Exactly which Selkirk product did you use, it seems they have a bunch? Just saying double wall does not help enough.
Dave Klish, I recently ordered a 2x6 wood fired evaporator from A&A Sheet Metal which I will be converting to oil fired
Now have solar, 2x6 finish pan, 5 bank 7x7 filter press, large water jacketed bottler, and tankless water heater.
Recently bought another Gingerich RO, this one was a 125, but a second membrane was added thus is a 250, like I had.
After running a 2x3, a 2x6, 3x8 tapping from 79 taps up to 1320 all woodfired, now I'm going to a 2x6 oil fired and a 200-425 taps.
Maple flats see below. I need to go from the male end to a single wall SS stack that I previously used from SLM.
Jay, the 8DSP-CPA is what I call the male adapter. I need the female adapter. Thanks!
https://www.amazon.com/Selkirk-20800...-garden&sr=1-2
2014 6 Taps Block Arch and momas canning pot, 3 gallons YIKES
2019 100 taps and a new adventure with a home built arch.
2020 90 taps, my wife and I and a Bucket RO...
2021 112 taps and a modified Bucket RO.
2022 120 taps, modified Bucket RO a Wife, Son and Springer
If your piping from the arch up to the adapter is with the single wall then the double wall above that this is what is recommended because you install the pipe "upside down" so that condensation will drip inside the pipe and not run outside of it. BUT that said in most arch setups temps run so much hotter than a wood stove that its not necessary to worry about the condensation.Originally Posted by red/one
You could use this adapter and just cut off the reduced end of the last single wall section to fit??? just a thought Jay
Zucker Lager
Chimney.jpg This is what I need to adapt to. Its already sealed in through the roof. Thanks!
2014 6 Taps Block Arch and momas canning pot, 3 gallons YIKES
2019 100 taps and a new adventure with a home built arch.
2020 90 taps, my wife and I and a Bucket RO...
2021 112 taps and a modified Bucket RO.
2022 120 taps, modified Bucket RO a Wife, Son and Springer
Keep the single wall for later use, and continue up with the needed height with double wall. That is how I completed my set up with my SL evaporator.
2004 - 2012 2x3 flat pan 25 to 60 taps
2012 2x3 new divided pan w/draw off 55 taps
2018 - didn't boil surgery - bought new evaporator
2019 new SML 2x4 raised flue high output evap. 65 taps
made 17 gal. syrup
2020 - only put out 53 taps - made 16.25 ga.l syrup
2021 - Didn't work out
2022 - 25 taps on bags / 8 taps on 3/16's line - late start
Going back to what Jay said, the single wall crimped end fits into the double wall end. I was thinking the crimped end was always away from the unit when in fact it should be facing the unit. So I have read...
I will install my single wall into the double wall crimped end first and put a storm collar on to cover the "shoulder" of the double wall pipe. Thanks!
2014 6 Taps Block Arch and momas canning pot, 3 gallons YIKES
2019 100 taps and a new adventure with a home built arch.
2020 90 taps, my wife and I and a Bucket RO...
2021 112 taps and a modified Bucket RO.
2022 120 taps, modified Bucket RO a Wife, Son and Springer
Posting Permissions
Reply With Quote