You can build a 6000 gallon tank for less than $2500.
https://www.youtube.com/watch?v=xc_J2ZETqzk
You can build a 6000 gallon tank for less than $2500.
https://www.youtube.com/watch?v=xc_J2ZETqzk
Mark would you happen to know the folks that built the tanks? Just wondering where I could find a materials list and blue prints.
Maple Man 85
About 750 taps on High Vac.
2.5 x 8 Intens-O-Fire
Airtech 3 hp LR Pump
Springtech Elite 500 RO
14 x 24 Timber Frame SugarHouse
16 x 22 Sap Shed w/ 1500 gal. + 700 gal. tanks
www.littlehogbackfarm.com
Thanks Mark, not tough to build just some time and a lot of welding, cutting and measuring. Based on the prices I am building my own!!!
That looks like 20 or 22 gauge stainless based on how it flexes. Butt welding many linear feet of thin stainless is not as easy as some people think. If you use heavier stainless it will weld easier but will be much harder, heavier and more expensive to work with.
Larger size factory tanks can be had for around a dollar a gallon and are a bargain at that price unless you have serious fab skills and the brake, tig and tools needed to put it together.
Personally if I was building a big tank like that I wouldn't but weld it, I would either make the end piece a quarter inch longer or set it inside the 2 end a quarter inch, then you have a nice corner/ overlap to fill . Yeah it may not look as good as a polished up pro made tank, but it will be rugged for sure.
Nate Hutchins
Nate & Kate's Maple
2022 1000 taps?
3x10 Intensofire
20x36 sugarhouse
CDL 600gph RO
A wife and 2 kids.
Would there be a difference in cost, strength...... If you soldered the tank with lead free solder?
Obviously it wouldn't be as pretty but to some of us I'm assuming fuction over flash is ok.
The early stainless steel tanks made by sugaring manufacturers were soldered. If you moved the tanks around much or they weren't supported well on the ground when frost was coming out the solder would crack and leak. Some manufacturers like CDL are making tanks cheaper by using thinner stainless steel, but in larger tanks there is issues with stainless steel buckling when they are moved around.
Sugaring for 45+ years
New Sugarhouse 14'x32'
New to Me Algier 2'x8' wood fired evaporator
2022 added a used RB25 RO Bucket
250 mostly Sugar Maples, 15% Soft Maples. Currently,(110on 3/16" and 125 on Shurflo 4008 vacuum, 15 gravity), (16,000 before being disabled)
1947 Farmall H and Wagon with gathering tank
2012 Kubota with forks to move wood around
Well, I took Motowbrowne, BreezyHill and Maple Flats advice and purchased the 250 gallon DeLaval bulk tank. Thanks. There is not a valve on the end of the outlet, two lids need to be found, and the thermometer on the front of the D250 doesn't read correctly. Any idea where a guy can get parts? Also, I have been searching the web for an exploded view of the tank to see what it looks like under the outer skin. I have not had any luck. Any ideas where I could find a diagram like this? I ended up getting it for $200 so I'm satisfied for the price. Any help would be appreciated.
Last edited by DocsMapleSyrup; 07-27-2016 at 04:36 PM.
Chad
2014: 12 taps, 5 gal buckets
2015: 15 taps on bags
2016: 150 taps: 100 on bags, 50 on 3/16" natural vac, 2x8 AUF/AOF Homebuilt Arch, 2x8 SL Drop Flu & Auto Draw, SL Propane Canner/Bottler
2017: 225 taps: Built Lean to, Added SL hood, preheater, concentric exhaust, SL SS 7" SB Filter Press
2018: 180 taps: Added Shurflo to 50 - 3/16", Auto fill sensor to head tank
2019: No tapping
2020: 175 taps
2021: 300 taps, homemade RO and releaser
2022: 600+ taps