Search:

Type: Posts; User: OGDENS SUGAR BUSH

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds; generated 18 minute(s) ago.

  1. Replies
    2
    Views
    852

    usually the manufacturer has the best advice....

    usually the manufacturer has the best advice. Stick with what they say
  2. Replies
    7
    Views
    2,767

    sodium hydroxide

    sodium hydroxide
  3. I also purchased Darryls press and hand pump, but...

    I also purchased Darryls press and hand pump, but after 1 year i upgraded to an air pump. i can press between 10/13 gallons per set of papers. it all depends on how bad the sugar sand is
  4. Replies
    13
    Views
    3,352

    there is no way a 1/2 hp pump is going to run a...

    there is no way a 1/2 hp pump is going to run a 330 procon and after reading your post again, go with at LEAST a 1hp motor
  5. Replies
    5
    Views
    1,751

    I had the same problem couple years ago not real...

    I had the same problem couple years ago not real sure what caused it but i think sap leaked past the U ring on the concentrate end of membrane
  6. Replies
    16
    Views
    3,014

    sap enters the outside port on all your membranes...

    sap enters the outside port on all your membranes and concentrarte comes out the opposite end on the outside port. Permeate comes out the center port
  7. Replies
    7
    Views
    2,484

    When you wire up the pump by pass the pressure...

    When you wire up the pump by pass the pressure switch
  8. Replies
    4
    Views
    1,485

    yes usually after 8% pressure starts to climb and...

    yes usually after 8% pressure starts to climb and i would have to open up the concentrate needle valve to keep the pressure down and the flow up
  9. Replies
    4
    Views
    1,485

    I use 3 4x40s and with recirculation i get to 10...

    I use 3 4x40s and with recirculation i get to 10 sometimes 12%
  10. Replies
    6
    Views
    1,776

    Just curious if you have any kind of relief for...

    Just curious if you have any kind of relief for the procon pump
  11. Replies
    1
    Views
    883

    yes you can, i just bought 20 from Menards today

    yes you can, i just bought 20 from Menards today
  12. Replies
    5
    Views
    2,195

    https://www.freshwatersystems.com/products/hydroni...

    https://www.freshwatersystems.com/products/hydronix-adjustable-panel-mount-flowmeter?variant=13250147319851

    or you could do this
  13. Replies
    8
    Views
    5,486

    looking forward to seeing everyone again this year

    looking forward to seeing everyone again this year
  14. Replies
    23
    Views
    11,895

    temp should be 211f when you use the hydrometer

    temp should be 211f when you use the hydrometer
  15. 12 volt battery ,Zomodo camera and smarttalk...

    12 volt battery ,Zomodo camera and smarttalk hotspot
  16. Replies
    13
    Views
    3,248

    have you checked with Bill Mason, he is located...

    have you checked with Bill Mason, he is located in Chapel Maine
  17. I used HOT water and baking soda, and triple rinse

    I used HOT water and baking soda, and triple rinse
  18. Replies
    9
    Views
    2,435

    you should be able to remove at least 90 gals of...

    you should be able to remove at least 90 gals of water per hour with your new set up
  19. Replies
    5
    Views
    3,588

    you can do this but you need to add the solid...

    you can do this but you need to add the solid plate also and lengthen the bolts that hold it together
  20. Replies
    13
    Views
    9,631

    https://www.ebay.com/itm/Hubbell-Industrial-Contro...

    https://www.ebay.com/itm/Hubbell-Industrial-Controls-69WC7-PressureSwitch-3-20-CutOff/223309859315
  21. Replies
    13
    Views
    9,631

    low pressure shut off is nice when you want to...

    low pressure shut off is nice when you want to leave the R/O unattended to do other things and it will shut down when it runs out of sap
  22. Replies
    10
    Views
    8,917

    I use the same setup, i have always left...

    I use the same setup, i have always left everything intact and the barrels have always been sealed. I fill them at 200 degrees
  23. Replies
    33
    Views
    19,960

    looks good Clay, like you said much nicer than...

    looks good Clay, like you said much nicer than standing outside
  24. I installed the small releaser from lapierre in 2...

    I installed the small releaser from lapierre in 2 different woods. built small sheds for tanks and equipment. pretty much good to go after starting them each morning. Trouble with ladders is takes...
  25. Replies
    19
    Views
    9,845

    Bascoms has a couple large tanks inside their...

    Bascoms has a couple large tanks inside their building. it would have to be refrigerated
Results 1 to 25 of 499
Page 1 of 20 1 2 3 4