My releaser came with a check valve. It was just loose and not installed anywhere.
I originally hooked the releaser up without it installed and it pulls a vacuum through the pump out line while not...
Type: Posts; User: Bricklayer
My releaser came with a check valve. It was just loose and not installed anywhere.
I originally hooked the releaser up without it installed and it pulls a vacuum through the pump out line while not...
My releaser came with a check valve. It was just loose and not installed anywhere.
I originally hooked the releaser up without it installed and it pulls a vacuum through the pump out line while not...
Where is the check valve be located in your pump line ?
I had to put mine at the end of the vertical line where it switches to gravity
Is the hole in the 90 fitting or the actual pump line ?
Anyone have a CDL vertical releaser with the submersible ( well ) pump inside the releaser ?
I would love to know where CDL was supposed to put the hole in the outlet. Mine has no hole at all. ...
I have a 3 phase Busch R5 vacuum pump that I just set up with a VFD.
Pump runs amazing with it. But I’d like to be able to install a vacuum sensor that controls the speed of the pump so it will not...
I have the barometer from Plymouth sugarworks. It shows the boiling point of water in real time and target temp for syrup based on that reading.
It has been spot on all season.
It can be shipped. Just has to be in an approved tamper proof package and Probley another 100 requirements. It’s a white powder. So usually draws attention when being shipped. That’s what I was told...
I buy mine bulk at a health food store.
And have bought it at bulk barn before as well.
It’s Probley a leaky joint or a small crack in the housing.
I had a small leak in mine where the pipe goes into the releaser. It would produce little tiny bubbles around where the leak was. I had...
I run one of my vacuum pumps off a 4000 watt inverter generator.
Lasts 10 hours running the 1hp electric motor on the vacuum pump.
But the kicker is I have to have my big 8000 watt generator done...
I turned my pumps on at 12:30 today and sap was comming in good. Sun is strong today.
Usually wait around for the first couple releaser dumps after a good freeze up. Sometimes there is a surge of...
Couple other factors that effect boil other then the things mentioned.
Cleaning the underside of your syrup pans in the off-season. I used to do the flue pan too but can’t do that anymore. So I...
All those things are great improvements and will help with your boil.
Does your evaporator have forced draft ?
This is my first year with our new 2.5 x 10 Venturi and after 3 boils I installed...
The nitre is very fine this year.
I drained my front pans today expecting to have to let them soak a day or two to get the nitre off. But it just hosed right out.
Just a fine silt on the bottom....
I always tell my wife there are worse things I could be addicted to.
Of course you can add it.
As long as it’s good syrup and there are no off flavours in last years batch.
This is my first year with my new wood fired CDL Venturi evaporator.
Just wondering what is the process of cleaning the underside of the back pan.
In years past with our smaller evaporator we...
Couple things can go wrong with the way you are doing it.
#1 - I assume it’s a steam bottler with the water tray under the bottling tank.
Not a good idea to have it up to temp and them filter...
I have had my RO set up 3 different ways with 4” membranes.
1 single 4” , 2 x 4” in series , 4 x 4” in series/parallel
The maximum I was able to get sap concentrated to before the flows slowed...
Mine has no hole at all.
The pump head sits horizontal and has a clear braided tubing from pump to pump outlet with a sanitary Tri clamp fitting holding it together. No hole at all.
I would...
Does it have the pump inside the releaser ?
I have 8 of those that came with my evaporator. I will Probley never use them. Every port on the evaporator has a valve. So only time I would ever use one is if I had to take the valve off or the...
This year I installed a CDL horizontal electric releaser in a remote pump house in our new bush.
Is only about 18” high and basically sits right on the ground. It’s got a submersable well pump head...
Finished tapping yesterday. Spent hours today chasing down leaks and more deer chews. Problems with an electric releaser. Etc.
This is the first time I’ve ever ran my vac pumps all day and all...