Good to hear, is this something D&G could do? I have a local dealer that is good to work with, not sure if they need the RO sent.
Type: Posts; User: jmayerl
Good to hear, is this something D&G could do? I have a local dealer that is good to work with, not sure if they need the RO sent.
There is a listing for one that is expanded right now in the classifieds. I also figured it would be since it has the larger 7.5hp motor. There was two motor sizes listed and this one has the bigger...
Does anyone know if it is possible to get a expantion kit added to a springtech elite 600 by anyone?
So I have buyers remorse on a used springtech 600. I bought it to upgrade from my 250 and since I bought it from the other side of the state I only had the sellers contact info on messenger.
Well...
Just fried the new contactor after about 6 hours of running. I smelled some electrical and by the time I got the infrared thermometer on it it was 150 degrees then blew…… WTF22982
After swapping a couple parts out, it was the main contacter switch, $125 in stock at the local electrical shop.
Did you guys just jumper the low pressure shut off to test it. I talked to Ray and he was of zero help.
Calling all electricians……deer run 250 shut off today during a low pressure wash. Obviously electrical problem. I checked the outlet and still have 240v at the out let. I have zero electrical...
I pay about $1400 a year for coverage on the 24x 60 sugar house, tractor, Argo, 50k in contents, 2.5 mil in product liability.
https://fb.watch/coahnlp6RU/
Had one here in NE Wisconsin two days ago go up in flames also
This will be my decision over the next month, will be getting a 600 RO, just not sure between the CDL or the memprotec
Spoke with mark from nh and he suggested replacing the o rings , so took it all apart and replaced the upper and lower cap inner and outer o rings, put brand new out of the package mes membranes in...
Yes , this is how I have this set up right membrane with flow arrow up and u cup as you have it; and left membrane with flow facing downward and u cup as you have it….. what flow rates are you...
What is anyone with a Deer run 250 seeing for concentrate and permeate flows? My flows are almost opposite this year with my new MES membranes in it. Permeate is 1.5per minute and concentrate is 4...
I know the design/ builder well, he is 30 minutes away and runs a decent size sugar operation. Multiple units were beta tested last season and they felt worked very well. He has an engineering...
Lip up you mean like a ^ and lip down you mean like v, if looking at it from a profile view? Correct?
Forgive my confusion but I took my membranes out last year to store in containers for the first time and needed to remove the u cups to fit in. I now can’t seem to remember the proper location and...
So I am an electrical idiot... how does one properly wire these motors for 220 and what kind of switch to use. I assume a relay is always needed?
Yes it will help a little , I used DE with flat filters years ago before I got a press. I added 1/2cup per gallon.
Then if this is what you feel why was this not immediately moved to the classified ad section? That is where all for sale/buy ads go; this is a thread for discussion.
🤪🤪🤪🤪🤪🤪🤪🤪hahahahaha
You are a bit confused on the name, it is called maple cream.
Does anyone have knowledge on the functionality of older bulk tanks? I just bought a 150 gallon tank and was told it worked when last used 4 years prior. It is a dairy equipment company model 150. I...
I would bet my money on a bad weld, I can’t tell exactly by the picture but that seams most likely. If they don’t make the situation better I would sell it as soon as season is over and just get a SL...
As long as there is slope that is all that matters. WAY to many taps per lat. if it was a high vac system the best results would be with under 5 per lateral. I would never go over 7-8 but if they are...