I just want to let everyone in northeast Wisconsin know that we started carrying supplies for maple producers. We are not a full-line equipment dealer, but we have a lot of the consumables a maple...
Type: Posts; User: inthewoods
I just want to let everyone in northeast Wisconsin know that we started carrying supplies for maple producers. We are not a full-line equipment dealer, but we have a lot of the consumables a maple...
You can open the valve manually. You need to push the black button on the top of the bullimo (orange) controller. Push it straight down all the way, and it disengages the gear. Then you can turn...
you will have no problem, as soon as you get any amount of sap in your tank above the inlet of your ro you start to make head pressure. your not going to start your ro up with a couple inchs of sap...
drain a little water out of wash tank than take a pail of perm. and dump a little back in wash tank to get ph down. what soap are u using? i have same ro and use bio membrane soap and it takes about...
Once I get the maple syrup/taffy cooled down to room temperature, how long can it sit at room temperature before running it through the cream machine? I have let it sit for up to 24 hours before...
finished tapn my tubing section today, had vac on most of day and got 60 gal from 625 trees. not much happn here yet.
i had similar problems last yr, futzed with it every day until i epoxyed a .5 inch nut to end of float ball. im running about 26+ inchs. when i asked salesman for help he told me to create a vac leak...
I also bought a 600 expandable H2O last year, for the 2013 season. I'm very happy with it. It's very easy to operate. I never had any problems. The service from the dealer was excellent, and...
I am also an Operating Engineer Local 139.
Doc, are these numbers (by that I mean gallons per tap) usable sap during the season, or total sap (even the nasty/buddy sap after the buds break)?
On a separate note, I read your brief article...
put it in a bag of uncooked white rice, it will pull the moisture out.
Here's a couple pics of the main line tool I made. I thought I would try something a little different, and eliminate the vise grips and make it so you can use one tool for all size main lines. I made...
Where are you located in Whitelaw? I'm just a few miles south of you. I would be interested in buying your sap. Stop over to see me so we can talk about it, or give me a call at (920) 242-9050.
...
very very nice. need more pics!!!
I had some free time this afternoon, and it was raining outside, so I put together a main line drill. I'll get some paint on it tomorrow. Larry (lpakiz) machined out the 5/8 bolt to accept the drill...
Check out this link on the trader in the classified. If this is what you're looking for, I have a few of them left.
...
SDDave~
The burners are about 6 1/2 inches apart. The BTU's I don't know about. The burners came out of a 75,000 BTU furnace. I have a high pressure regulator with my propane tank, and can get a...
Here's a couple pics of the burner stand that I made for my warming pan. The burners are stainless steel and came out of a forced-air furnace. I made the gas manifold out of a piece of 1/2" pipe,...
I had the same problem you did. I didn't want to walk down to my tank every half hour to see if it was full. All I did was buy a toilet tank float for under a dollar. I took a piece of...
i use 35% peroxide diluted down to 5% to clean my lines at the end of the season, works very good. i dont know the exact chemistry behind it, but i know it breaks down with time and turns to h2o. you...
adamski,s sugar bush, antigo wi 715 623-6853 very nice people.
sippl,s sugar bush,birnamwood wi. just south of antigo 715 216-4627, 715 449-3426.
both places sell maple syrup equipment and supplies.
I will also be at polaks open house tomorrow
Here's a picture of the temperature controller that I built for my vacuum pump. The temp controller is a Ranco. I purchased it from Grainger for approx. $73. You can buy them off of E-bay for...
Just received my new personalized license plates today.
I couldn't believe that "Got Sap" was available.
Does anyone else have personalized plates pertaining to mapling?
manitowoc wi = 300 on vacuum