Search:

Type: Posts; User: davey

Page 1 of 10 1 2 3 4

Search: Search took 4.12 seconds.

  1. Replies
    7
    Views
    3,904

    I would first try to figure out what rpm your...

    I would first try to figure out what rpm your engine runs well with good power and efficiency. Then if you put possibly a three inch pulley on the engine you should be able to dtermine the pump...
  2. Replies
    40
    Views
    15,723

    thanks, will do.

    thanks, will do.
  3. Replies
    40
    Views
    15,723

    Nice job in the article, your sugarhouse looked...

    Nice job in the article, your sugarhouse looked very good.
  4. Thread: Mendon NY 2012

    by davey
    Replies
    5
    Views
    3,282

    I'm nearly tappped, should be able to boil by...

    I'm nearly tappped, should be able to boil by wednesday at the latest.
  5. Replies
    12
    Views
    4,639

    I have all sorts of different options. Call me...

    I have all sorts of different options. Call me or stop over
  6. Replies
    13
    Views
    7,444

    My first year I didn't even tap. I just stuck a...

    My first year I didn't even tap. I just stuck a milk jug over a broken branch. I'd say you are way ahead of where I started. Have fun this year. Stop over anytime, I'm not too far from you
  7. Replies
    8
    Views
    4,807

    the first thing you need to determine is what rpm...

    the first thing you need to determine is what rpm the pump is supposed to be run at. After that just determine a speed slightly above an idle for your engine, do the math to figure the ratio from...
  8. Thread: tapping bits

    by davey
    Replies
    39
    Views
    18,239

    We did an experiment this year as I could only...

    We did an experiment this year as I could only find one of my Lapierre tapping bits. Two of us were tapping and I was using a standard bit and my buddy the tapping bit. I used up three fully...
  9. Replies
    5
    Views
    3,195

    I've ordered directly from Voorhees before and...

    I've ordered directly from Voorhees before and was very satisified
  10. Thread: vacumm tank?

    by davey
    Replies
    9
    Views
    3,821

    Its better to use the tank. If you can find an...

    Its better to use the tank. If you can find an old air compressor, those tanks work pretty good.
  11. Thread: Dealer

    by davey
    Replies
    2
    Views
    2,420

    Para-Deys Acres Maple in Macedon NY is a Lapierre...

    Para-Deys Acres Maple in Macedon NY is a Lapierre dealer. 585-259-9878
  12. Replies
    3
    Views
    3,030

    fence it in and get a herd of goats

    fence it in and get a herd of goats
  13. Replies
    3
    Views
    2,657

    If you go to a heating supply store, not a big...

    If you go to a heating supply store, not a big box, you can get sight glass tubes and mounts pretty cheap usually. I looked on McMaster and Carr and they had alot of different choices that would...
  14. Replies
    3
    Views
    2,388

    gas engine powered SP22

    If anyone is running a gas engine on an sp22, can you post the HP, rpm range and pulley size you are using if you know them?
    thanks
    Dave
  15. Thread: pex preheater

    by davey
    Replies
    4
    Views
    2,698

    pex preheater

    Any thoughts?
  16. Thread: Tapping 2011

    by davey
    Replies
    15
    Views
    7,814

    got the blow downs cleaned up, the old lines...

    got the blow downs cleaned up, the old lines repaired, currently stringing some new lines, rebuilding the vacuum pump engine, fixing the trailer, straightening up the sugarhouse, .... should easily...
  17. Replies
    8
    Views
    4,501

    We did the same with tub caulk, cleaned it a...

    We did the same with tub caulk, cleaned it a litttle and stuck it on. used to fix my horse's water tank that way and it always held up then too, just smear it around good.
  18. Replies
    10
    Views
    4,769

    You are right, its just that the problem is now...

    You are right, its just that the problem is now self-employed, at least for the time being.
  19. Replies
    10
    Views
    4,769

    And what a huge improvement in service that...

    And what a huge improvement in service that shakeup of employees has made there
  20. Replies
    4
    Views
    3,267

    the laser thermometer will usually only read the...

    the laser thermometer will usually only read the steam coming off of the syrup as that is the first thing the beam hits and reflects back from. It would be nice if they worked, but from experience,...
  21. Replies
    12
    Views
    5,462

    If you are anywhere near Rochester, you are...

    If you are anywhere near Rochester, you are welcome to come see my set up.
  22. Replies
    16
    Views
    5,809

    I wonder how much time people who blame the...

    I wonder how much time people who blame the teacher's unions for their child's poor education actually put into ensuring that their child gets whatever educational needs necessary when they live in...
  23. Replies
    13
    Views
    7,621

    I used it last winter. unfortunately, our season...

    I used it last winter. unfortunately, our season was pretty short so I can't make any big statements as to that. the little bit I did though it worked fine. The tank is made of polyehtylene so it...
  24. Replies
    13
    Views
    7,621

    I went with this one instead to avoid the...

    I went with this one instead to avoid the galvanized....
  25. Replies
    19
    Views
    11,779

    We have always pulled on the pallet/cribbing that...

    We have always pulled on the pallet/cribbing that we built. This prevents damage to the tank as then it is just a passenger and not being pulled upon directly. Any strapping to the tank should be...
Results 1 to 25 of 235
Page 1 of 10 1 2 3 4