Search:

Type: Posts; User: kinalfarm

Page 1 of 5 1 2 3 4

Search: Search took 0.01 seconds.

  1. Yepper, just as you have it in the drawing.

    Yepper, just as you have it in the drawing.
  2. Thread: saw decision

    by kinalfarm
    Replies
    31
    Views
    14,379

    My husky 365 puts a woopin on my brother inlaws...

    My husky 365 puts a woopin on my brother inlaws stihl ms361
  3. Replies
    14
    Views
    5,208

    It sounds like it's probably a finisher?

    It sounds like it's probably a finisher?
  4. Replies
    9
    Views
    3,867

    Tin pans are fine. They have used them longer...

    Tin pans are fine. They have used them longer than stainless just more susceptible to scorching warping and don't last as long if you don't take care of them
  5. Inwould run the dividers the other way in the...

    Inwould run the dividers the other way in the front half because you want to draw syrup off on the hottest part of the pan which is usually the middle which would be the back of the front(syrup)...
  6. The problem is the ramp. I would do what your...

    The problem is the ramp. I would do what your talking about and raise the ramp and maybe even the grates. If your running a blower than make sure it's the right size maybe around 200 cfm. And also...
  7. Replies
    6
    Views
    3,474

    Dry wood, sap level and combustion air is what u...

    Dry wood, sap level and combustion air is what u need. Should be getting at least 35gph
  8. Replies
    4
    Views
    3,006

    I built a pan like that this season. If you pm me...

    I built a pan like that this season. If you pm me I will send you pics. Via email or text. Also the thread is still up under drop tube flu pan.
  9. Replies
    27
    Views
    12,726

    Spencer, I would put only 2 taps to every 5 gal....

    Spencer, I would put only 2 taps to every 5 gal. Bucket because they will run over in one day if it runs good.
  10. Replies
    3
    Views
    2,028

    Try it! I am the guy that did them under the pan...

    Try it! I am the guy that did them under the pan and I'm boiling about 22 gph I made 4 gal of syrup yesterday on my arch they work great because the cold sap coming in gets sucked into the tubes and...
  11. Replies
    4
    Views
    2,662

    I have a sheet of plywood covering my head tank....

    I have a sheet of plywood covering my head tank. I just cut a small round hole to accept the snap on filters and they have a plastic ring sewn in the top so it
    Can't fall through my hole and pump...
  12. Thread: gph question

    by kinalfarm
    Replies
    13
    Views
    4,859

    Hi, to answer your question, my 2x6 got about 12...

    Hi, to answer your question, my 2x6 got about 12 gph before I added a blower after the blower I was getting about 16 than I pipe pipes under the back pan and I'm now getting 22-25. Hope this answers...
  13. Replies
    78
    Views
    47,392

    45$ gallon / 25$ half/ 15$ qrt don't sell...

    45$ gallon / 25$ half/ 15$ qrt don't sell anything smaller
  14. Replies
    17
    Views
    8,049

    Really? I'm in clymer,NY and it has just been...

    Really? I'm in clymer,NY and it has just been average. Get er' dun
  15. Replies
    122
    Views
    43,820

    48 yes - 5 no

    48 yes - 5 no
  16. Replies
    26
    Views
    10,390

    I have a ranger 500 4x4 and I can fill My...

    I have a ranger 500 4x4 and I can fill
    My 110'gallon tank and haul it anywhere! Boo on jd
  17. Replies
    11
    Views
    4,306

    I was always told that the spot that you draw off...

    I was always told that the spot that you draw off from should
    Be a hair lower. Is that correct?
  18. Here is a little piece of advice for adding...

    Here is a little piece of advice for adding dividers. You want to drawnthe syrup off from the hottest part of your pan. if that happens to be the middle than put two dividers in 18" long then put as...
  19. Replies
    17
    Views
    15,215

    I'm not sure how much you know but sometimes if...

    I'm not sure how much you know but sometimes if you tap when it's below freezing you can crack the bark around the tap when you drive it in which also causes leaks. But as someone already mentioned...
  20. Replies
    3
    Views
    2,037

    You might want to think about putting a vent it...

    You might want to think about putting a vent it your float. As the air inside expands it tends to find a way out.
  21. Replies
    3
    Views
    2,103

    The guy that built my pan just tacked the...

    The guy that built my pan just tacked the dividers with a tig than he silver solders
    Them so it wouldn't warp. If you use a iron it works pretty well but a torch is harder to use.
  22. Replies
    48
    Views
    19,904

    veiw the video

    http://www.youtube.com/user/2012sugarin finally got it uploaded. thanks for your patience
  23. Replies
    48
    Views
    19,904

    Boiled this morning I only had 100 gallons and...

    Boiled this morning I only had 100 gallons and the tube pan performed great I boiled I 4 hr. With start up time. I can e-mail the video to anyone
  24. Replies
    48
    Views
    19,904

    Thanks for the complements and Constructive...

    Thanks for the complements and
    Constructive criticism:)I have to clean pans and filter tank and
    Put my pans On the arch and mount feed
    Tube and float valve and clean tanks and pumps then I can...
  25. Replies
    48
    Views
    19,904

    Vordu, I used stainless steel grab bars for my...

    Vordu, I used stainless steel grab bars for my drop tubes. I got 40 taps out tonight before it got dark so we will see
    How it does soon. This pan is hooked
    To my other pan(syrup pan) so it's...
Results 1 to 25 of 110
Page 1 of 5 1 2 3 4