Search:

Hello all i am having a new installation done and had the mfg rep and installer came out to lay it out and do my material list.
They are proposing a single line system 2 1-1/4 mains at approx...

How much are they asking ? im looking at a rc 0063 its 3hp here in Ontario They need a moisture trap for sure and a VFD in most cases. My research has found a lot of these vaine pumps are used...

Cdl has the clear hose for these, it's thick wall and will take over 100 c

I agree with Haynes. auto draws are personnel , I use a cdl , new last year, calibrate every day and mostly twice a day , as the barometric pressure changes so does your boiling temps. We strive for...

my first blower was one of those 5" heating duct booster in a heating duct pipe. of course. into a 3x10 boot .took the vent door off my ole lightning 2x6 arch and the square part of the boot fit not...

i am just starting to tap on fri and looking to go till easter! ribbet ribbet ! lol

well cold again tonight and tomorrow high of minus 8 low -14 with wind chill -30 nice! going to tap late this week. long range has finally got some consistant - / + in it over the next few...

Iv been using CDL 5/16 health spiles for a few years now and havnt expierienced any issue .

Jeff, Mines not running ! we havnt even tapped yet, aside from tue and wed this week the long range for me is cold as far as i can see to the 13th. Even with the high tue and wed of 6 there is rain...

Not tapped here yet. A couple warm days but the 14 day has it cooling down to some double digit minus temps. Most of my bush is north facing and we are always a couple weeks behind the lower...

stay away from PJ evaporators (phaneauf ) workmanship is second to none just doesnt deliver , i ordered fall of 15 with del set for late Feb 16 got it in june but missing blower motor and some...

The omspa (Ontario Canada). Recommends not washing new bottles. When you buy new they are packed upside down and will never be cleaner than then . as soon as you put water in them no matter the temp...

Doesn't sound like too much aid ,if it was your pressure would go up. Papers on the right side?plates on the right way so bypass holes line up ?
Syrup is Hot 200 deg. ? Run thru the pres back into...

Hello 870. This is only what I would do. First loose the cheese cloth. (Did that come from the book backyard maple). Bring your batch to syrup 67 brix is best then filter when hot. To filter...

Thank you Dr Tim.

Mule

Peter. Dry wood for a traditionial arch Is a must. What size is it Split? Split it small I mean small 2" x2" max and fire often every 2 min or so . a tip when firing/loading only open 1 door...

No way I know or heard of to lighten syrup . a filter presswill lighten it a little but not a grade or so colour has everything to do with boiling time and heat and also pan cleaning. You said you...

Relax. I sold my evap cause my new one was due last week !no show !! I hope it snows and freezes till April !!!! Lol

Mike

Guys CDL have. Regional sales people that will set u up with what you need. Either by shipping or pick up. search the cdl site an call or mail your rep for stuff . they are very easy to access ...

That program may be OK if you are a major producer 25k + taps and don't mind the govt all over you. The paper work and process a nightmare!
What I was saying\ meant was that as small producers...

What kind of filter are you using ? If you syrup is at 67 brix it won't filter at room temp. Syrup should be 190/200 deg f to filter. Nitre will start when syrup starts to boil. If you are using a...

Terry, the old rule was 1 litre of syrup per tapper season , I have never achieved that on a continuous basis. Short seasons, poor run , all kinds of reasons. I have SAP at 2.6 and then the same...

Check out smokey lakes new one with the compensator dial on the cup COOL !!

Mike

We are not subsidized one penny ! Not in Ontario ! Don't know where you got that from but it is BS. We can sell our product to whoever and for whatever we can get! We don't get kickback (subsidy)...

Pete. Buy a proper tapping bit 5\16 or 7\16 wich ever you are using for taps. Only drill in 1 1\2 " max don't wobble it and bore hole bigger or ream it .if you are using pails drill on no more...