2166421665 just a few of my past installs.
Type: Posts; User: jason grossman
2166421665 just a few of my past installs.
Just a quick question here, since we cannot use iso alcohol to clean because it is not labeled for cleaning tubing. how is calcium hypochlorite being used. Mr.
krueger was using cal-shock, which is...
The pumps were travini em28s similar to airtech or atlas small but mighty. 19cfm 28in vac.
We used direct bury triplex. 2,2,4. We are aslo required to ground back to the source just not a ground rod at the load end, so that was 6 wire. So 4 wires total. We were supposed to step a size down...
This may not apply to you, but in the past few years I have built many small opertions that we have been running electric to the woods. Using small vac pumps and electric releasers to pump sap out. I...
That membrane should be washed different than what was in there originally. Ph is different. H20 recommends liquid bio membrane cleaner, also an oxisan wash and citric acid depending how high you...
I have used the helical wire splices in my tubing installations for years now and it is the fastest and strongest way to end wire or splice it. I also distribute them for preform line. I have them...
For years lapeirre did installations with 2in pvc dry line and 1 1/4 wet line all on a 5/16 cable side tied with 9ga soft wire. I have installed some this way and rebuilt some. These were very good...
Do one better and s.s. lash it.better than ties faster and way cheaper than a tie gun that works most of the time.
Reme
Remember numbers are just that. It is a learning curve to go from 18in to 24 in. Then to run above 24 there are two big factors, can your system handle the increase and it takes a lot...
I work with tubing for a living and have used all brands, and I think what you are looking for is a cdl flex, or ipl 4 seasons. Lapierre ultra a, or h2o flex will also do fine. If you want flexible...
I have used a lapeirre sap pump for 8 seasons now and they work very well.we move 1800 taps 40 vertical feet and 1100 horizontal feet.it use to pump it 2000 feet but we cut it done alittle.
logging can be done very easily and to a full extent after a pipeline system is installed. IF proper planning and installation is done. tubing installations can be done to allow full access to the...
ditto for me also theron. sometimes the loudest voices are not the best. there is starting to be way too much I'm the greatest do what I say and less can I help you have a good experience.
my tool is a hand tool it does not travel on the mainline. you cant use that the way i install. it is very hard and takes way too much time to take the j2 lasher and jump it around side ties,...
I have used lashing wire for many years and just built a tool myself. two hours of time and $25 dollars in materials. build a tool it is much easier.
cdl will be having an open house at the Timmons family operation in burton ohio on may 11 from 9 to 1. you can call 440-636-5371 for more info. I installed this high production wet/dry system in...
we have had a sirofilter for years. i would never go back to a plate press again. we can easily do a barrel or two before changing felts(which takes about 3min). if you want to go faster get two...
we use atlas aluminum snowshoes the have been the best for us so far. i have used all wood, all plastic and combinations and i really like the atlas shoes. they are quick rachet system with spring...
if you plan on doing vac in the future go for 5. if it does hurt the gravity oh well. otherwise you will spend a lot to redo it later. because 10 to 20 on vac doesnt do so well.
well mine is stronger than that. there are several different grades of it. we get food grade at 99% and dilute it down a little. it is hard to say what gets the best results(tubing instal, vac...
we have also been doing this for years. there have been studies done that show that you can transmit bacteria from hole to hole with the drill bit, regardless of temp. we have been using a sponge in...
i have used 2 and 3 inch in installations before. i will pass along a little advice. try to stay with 1.5 and make multiple runs. 2 and 3 inch are hard to handle, fittings are pricey, and they...
something you may want to check out. this system has been in use in quebec for several years and works well i have seen it at at least 5 different sugar operations of no less than 60000 taps each....
also wanted to mention that i will be around friday nite and all day saturday if anyone coming has questions about tubing installations or questions about their set up i would be glad to give advice.