I check the niter build up with the scoop feeling the bottom of the pan.last year we drained the front pan nightly and washed it with a acid cleaner just using permiate wouldn't do it.i have always...
Type: Posts; User: jimbison
I check the niter build up with the scoop feeling the bottom of the pan.last year we drained the front pan nightly and washed it with a acid cleaner just using permiate wouldn't do it.i have always...
I have a terrible niter build up in my pans during sugar season some of the basic info on my setup
4x12 Thor evaporator
4x8raised flue 4x4front
1800 taps plus 500 on halves for neighbor...
Thanks everyone
Most are 3-4 ft looking at using half inch rebar cheaper than others I have only about a 1percent grade need to eliminate any sags to maintain the grade
What are you using for the post to support your mainline I am running 1inch over 1inch wet dry would like information on spacing and post type, cedar, treated,rebar? thanks in advance
Will try it tomorrow thanks for the help
how far from the ladder are you putting the valve I added a new section have 20 plus on top 15 on bottom of the ladder no sap flow this is all new so very tight tried adding valve stem from tractor...
tried warming everything up used a salamander set up ten ft away warmed up to 60 on oil temp still no go its a robuschi pump new to me last spring used it to dry clean line [s then stored in garage
putting hand over inlet makes no difference,oil level is good when I shut it down in spring was working fine stored in garage for off season
hi I have a Indiana liquid ring gas powered pump started it before taking to the woods not pumping any oil so not making vaccum anyone have any experience with these
have mostly record multi fittings am looking to replace this summer any suggestions I have all black pipe for mainline all1 inch
I believe he now makes a 1000gph I just bought the 500 this spring from him if you need to look at one I am only about a half hour away from you
thanks for the info as I have virtually no smoke looks like I am burning propane most of the time, at night sparks are visable am firing at 12 minute timer, wood split no larger than 4 inches...
I am running a 4x12 raised flue burning 30 inch wood with AUF with a full boil front to back on both pans and only getting 550-600 degrees on the stack via infrared measure can get higher by...
I have put myself in the same boat 1600 taps on a 4x12 just ordered a RO from Ray is it better to concentrate less to give more boiling time or to go higher concentrate boil less set idle longer...
972697279728[attach=config]9729[/attach here are some pics hope this helps
must be the 75 not a 76 was told it was 76 ? had 5.25 pulley and 5hp motor now a Honda with 3.5 in pulley running at about 1/3 throttle it came as one unit with oil resivoir with reclaimer on top of...
thanks for the info just waiting to sell the barrels then will order now to just fill the woodshed again
can the kinney be used with oil to seal or just water
looking at Ray's RO also have not decided on the 375 or 500 running 1600 taps expanding to 2000 so probably the 500 anyone know if this can be gas powered or expandable thanks jim
no running water for cooling 1 mile from power have to use gas powered everything seen post on here where some are getting 25 + inches with these modified thanks for your help
Hi been lurking and learning for awhile but now need info how high of vacuum can reasonably be obtained with this pump now getting a solid 21 inches on 1600 taps with wet dry system have used the...
what would happen if you just cut a twig off and slide a 5/16 line over it no need to use a special cap just clamp the line and go to the next anyone ever tried son thought of this as we were...
could some one please give me some sugestions as last yearwent to all new stubbies and cv's new cv's this year started tapping Feb.14 by the end of March all lines had dried up except one that I had...
thanks for all the input this is the sixth year in this bush been adding from 600 taps as I go started in here 6 years sgo always made dark or darker started on 3x8 and hualed sap out of the woods...