Search:

Type: Posts; User: jrthe3

Page 1 of 20 1 2 3 4

Search: Search took 0.81 seconds.

  1. Replies
    4
    Views
    3,749

    Membrane cleanning

    Where do you guys send you membranes to get them cleaned. How do you ship them to get cleaned
  2. Replies
    13
    Views
    5,855

    perry that be great if you would i like to talk...

    perry that be great if you would i like to talk to someone that used propane
  3. Replies
    13
    Views
    5,855

    Three by Five foot

    Three by Five foot
  4. Replies
    13
    Views
    5,855

    i have a great leader dealer i been dealing with...

    i have a great leader dealer i been dealing with sense i went on my own bought every piece of equipment in my shack from them but they did not know to much about propane could order me what ever i...
  5. Replies
    13
    Views
    5,855

    I pretty much done with leader I taking my money...

    I pretty much done with leader I taking my money elsewhere every sense the new management take over at leader they treat people like dirt if you not making 10000 gallons a year and spend a 100k a...
  6. Replies
    13
    Views
    5,855

    3x8 propane conversion

    i want to covert my 3x8 raised flue evaporator over to propane i going to buy a propane gun looks like a fuel oil gun does anyone know how many btu propane gun i would need sense to calls to leader...
  7. Replies
    11
    Views
    6,175

    Well I was out fixing fence yesterday afternoon I...

    Well I was out fixing fence yesterday afternoon I noticed that some of the smaller soft maples are starting to get the little bud caps at end of branches not sure if this cold weather we going to...
  8. Replies
    7
    Views
    3,228

    I have a homemade auto drawoff I built I think ...

    I have a homemade auto drawoff I built I think the temp prob has a bad wire I got mad when It messed up and went and bought a real one but I sell it it a auber controller the prob the one that ...
  9. In my old sugar Bush I had before the parting of...

    In my old sugar Bush I had before the parting of ways me crossed a trail the cut down a hill side the trail had to stay open it was path to gathering tank we went on the low side of the trail found a...
  10. Replies
    11
    Views
    6,175

    Not ready to call it quits

    I not done yet going to see what this freeze and next week bring. Is anyone else with me on this ? Or am I all alone out here?
  11. Thread: any sap

    by jrthe3
    Replies
    2
    Views
    2,596

    just in from woods no buds in site i going to...

    just in from woods no buds in site i going to hang out for at least one more week see how things goes
  12. Thread: Defoamer use

    by jrthe3
    Replies
    30
    Views
    18,496

    i rarely use defoamer unless front pan is going...

    i rarely use defoamer unless front pan is going to foam over the dividers
  13. Replies
    8
    Views
    4,534

    Yes they can be I had my entire 3x5 raised flue...

    Yes they can be I had my entire 3x5 raised flue flue pan redone cost me around $500
  14. Replies
    8
    Views
    2,790

    When I was using cast Grimm grates in my 2.5 x8 I...

    When I was using cast Grimm grates in my 2.5 x8 I destroy a set of grates a season then I put a blower on it and the grates looked brand new five years later when I sold it talk to couple guys and...
  15. Thread: AOF question

    by jrthe3
    Replies
    26
    Views
    11,916

    When I built my arch I made to of the fire box...

    When I built my arch I made to of the fire box out of 2x4 1/4 in wall square tubing on sides and back and 4x4 1/4 inch wall on front nozzels 3/8 pipe 1/8 inch wall every 4 inch at bottom of tubing so...
  16. Replies
    9
    Views
    6,298

    My 3x8 raised flue with hoods and preheater and...

    My 3x8 raised flue with hoods and preheater and high pressure blower air over with heat exchanger on flue gases I running around 300 stack temps and 130 gallon of SAP an hour on our 3 x10 we had...
  17. Replies
    2
    Views
    1,576

    I have 12 inch flues with 12 inch of pan above...

    I have 12 inch flues with 12 inch of pan above top of flues then drip pan is 4 inch above to of pan
  18. Replies
    2
    Views
    1,576

    SAP in preheater drip pan

    My back pan is boiling so hard it is boiling over into drip pan for my preheater I tried running SAP level in pan higher and lower still doing it does anyone have this problem too any ideas on how...
  19. Replies
    9
    Views
    4,962

    Haven't had a freeze here sense Saturday night...

    Haven't had a freeze here sense Saturday night and SAP has not stopped flowing yet every bucket and drum over flowing every day vacuum bring it in faster then the RO can process It strangest thing I...
  20. Thread: crop insurance

    by jrthe3
    Replies
    0
    Views
    1,980

    crop insurance

    after having to change my lifes path and getting back into grain farmering full time have ben alot of dealing with crop insurance has anyone got or looked into crop insurence for ther maple crops i...
  21. I build my own ro

    I build my own ro
  22. the units i have seen of rays use presure wsaher...

    the units i have seen of rays use presure wsaher pumps from northern tool and motors from tractor supply the ro i have built have no problem running on 110 and use all food grade pumps
  23. Replies
    3
    Views
    2,156

    reversing flow on membrane

    we ben froze for couple days now so i ben doing some reading on leaders new ro. they have reversible flow on menbrane is that sap entering from oposite side on vessel i was thinking about setting my...
  24. Replies
    204
    Views
    82,781

    got half the vacuum tuhing tapped and most of the...

    got half the vacuum tuhing tapped and most of the gravity tapped had to fight threw waist deep snow cause snow shoes turn into skies on down hill slopes rest should be smooth sailing on snow shoes...
  25. Thread: March Journal

    by jrthe3
    Replies
    22
    Views
    11,767

    after 3 days of trying to fix leaks on my ro...

    after 3 days of trying to fix leaks on my ro after changing membranes i find out that the new caps i hard to order where brittish threads so ready to ring some necks
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4