Search:

I have a 1/2" Oberdorfer pump that has failed. I usually just buy a new one but has anyone had success with the rebuild kit they offer? It's $284 for a new through Dultmeier and CDL shows a repair...

I am extremely happy with mine, had it 6 years or so and not a problem and price was way better than going to one of the big guys. When you call with questions Art answers and he builds them! ...

That is sweet inthewoods! If only I lived in WI and could hire you! Those long tubes are exactly what I was looking for but will probably have to go with a camping type with 2 round burners.... ...

Keep the ideas coming, I appreciate the info. I have a 23 gallon vertical canner from leader and that sits on an old kitchen stove. I want to set up a large (or 2 of the round) propane burner and...

I'm looking for a propane burner that will sit under a +/-20 gallon flat pan for pre-heating syrup to filter and can in the off-season. Something with a couple of long tubes that will heat quick. I...

Dremmel and stencil set both great ideas! Thanks!

I'm buying some SS Barrels and want to know if anyone has ideas for affixing a label of some sort to to them? They are already manufactures so I can't have them stamped with my name.

I use Barcodes Talk, Inc. and they are a re-seller, $75 for 10 codes and I use stickers. I haven't had any problems and I'm in a couple of large grocery chains. Some chains like Wal-Mart do require...

I have had excellent luck with my 600 gph CDL RO for 2 years. Like another post said, I can do more than i expected and 1.0% sap will go to 9.5% without maxing out pressure. Instructions are simple...

I heard yesterday that the market already has a lot of filtered and un-filtered commercial and I would be taking my chances if I boiled and then wanted to sell the bulk. Unfiltered is only getting...

I'm in the next town over (Westford, VT) and am paying 0.75/tap if that helps.

I'm pretty sure they would be the same brand but I will check and see for sure and I also have a couple of extra new around I can switch out, they are definitly clamped down.... I just wonder if...

I'm replying to this thread rather than start new because it talks about quick connect or cam lok leaks. I have a few at road crossings under no tension and I can hear them leaking when up close. ...

I have a small space heater plugged into a temperature sensor set to 40. When temp. gets to 40 power comes on and heater runs until it is over 40 and shuts off. Also have a sensor wire that runs to a...

I've found if you install the saddle and then clamp it to the main, wire tie, then clamp the tubing with the one handed tool and place the flat metal side in the groove where the main line wire goes...

Same here, a small heated room and I have a small space heater plugged into a temperature sensor set to 40. When temp. gets to 40 power comes on and heater runs until it is over 40 and shuts off. ...

Just a follow up question on sucking the syrup out of the barrels, when using the press to do this it gets very loud and I figure this is just from the cold syrup? This is the first year i have used...

I was looking for info on this and found this old thread, thought I would continue it to answer my question... I have seen lots of larger (14 oz. tubes of grease and grease guns but what about...

This is after I scrub, drain, rinse, drain, etc. There are always little bits of stuff that I can't get to flow outand I've been trying to think of a way to suck them out. Also, not what you really...

Mine has the cleanout valve too but there is still a bunch of mung settled in the bottom of the flues. The 5/16 is a good tip and maybe I'll try duct taping a few together!

Has anyone found a good way to suck the crap out of the drop flues when you are cleaning a pan in place? I've looked for a Shop Vac attachment but haven't found one that fits my large Shop Vac that...

I did but it didn't sell well for me. I would recommend Cook-in-the-Kitchen http://cookinthekitchen.foodoro.com/ . They were great to deal with and the price was reasonable. For some reason the...

I pressure wash it every year and it still looks & works great at 9 years old. The best thing I learned is to use the proper lubricant from the manufacturer. I used different things before like...

I started a 10 year lease this year and have tubing up that I installed years ago when we had a handshake agreement. Since I've gotten more serious about sugaring I figured I better do something...

Last Thursday night I boiled some really ropey stuff that wouldn't filter or draw off well and thought I was done. Yesterday and today it's running o.k. and the sap has cleared up. Not sure if I'll...