Search:

Type: Posts; User: WMF

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    8
    Views
    1,475

    If I was graduating from homemade 4 inch...

    If I was graduating from homemade 4 inch membranes to an 8 inch I would watch adds for used stuff and buy a used name brand 8 inch post with built in recirc pump like a CDL.
    By the time you buy an...
  2. Replies
    15
    Views
    2,254

    If you don't have a coarse screen type filter on...

    If you don't have a coarse screen type filter on the inlet to the feed pump you probably have debris wedged in the impeller. Junk gets caught in closed impellers because they narrow near the outer...
  3. Your bill from the electric supplier is for...

    Your bill from the electric supplier is for power, not amps. There is no free lunch and a motor will use the same amount of power regardless of being configured to run on high or low voltage.
    The...
  4. Thread: Oberdorfer NL4000L

    by WMF
    Replies
    4
    Views
    1,472

    If you have not already done so you might try...

    If you have not already done so you might try tightening the gland nut as that will compress the packing material around the shaft and might stop your leak.
    I would rinse pump with hot water until...
  5. Thread: Oberdorfer NL4000L

    by WMF
    Replies
    4
    Views
    1,472

    Do you need the shaft seal or the thin paper like...

    Do you need the shaft seal or the thin paper like gasket that seals the two case halves? I think the shaft seal is just a packing like material that gets compressed by the gland nut the shaft goes...
  6. Replies
    6
    Views
    1,795

    You must use a laser printer. Ink jet will always...

    You must use a laser printer. Ink jet will always bleed if they get wet. Color laser printers are cheap now compared to what they were in the past.
  7. Replies
    44
    Views
    17,505

    I use electric level switch and motorized ball...

    I use electric level switch and motorized ball valve and pump directly into steamaway. I have a panel with flowmeter and bypass valve so I can adjust flow to a little less than steamaway is using and...
  8. Replies
    44
    Views
    17,505

    22383 When you look into your concentrate tank...

    22383
    When you look into your concentrate tank and see this you have no guilt about waiting a few days to boil. This was 14 brix about 29 degrees and is just slushy on top with the agitator always...
  9. Replies
    44
    Views
    17,505

    I have been experimenting with running chilled...

    I have been experimenting with running chilled glycol through the refrigerant jackets on a 2000 gallon Mueller for the last two years with good results.
    This still requires a glycol chiller which...
  10. Replies
    44
    Views
    17,505

    I have looked at the brazed heat exchangers and...

    I have looked at the brazed heat exchangers and have always been concerned with the inability to clean them. From my research the shell and tube type seem to be the best sanitary style but food grade...
  11. Replies
    44
    Views
    17,505

    What type of chiller did the dairy guy recommend?...

    What type of chiller did the dairy guy recommend? I know it is common for dairies to use a well water powered plate cooler to lower the temp into the 60 degree range and then they use refrigeration...
  12. Replies
    11
    Views
    5,434

    Just keep in mind with a two line setup you will...

    Just keep in mind with a two line setup you will be constantly filtering your whole tank of fuel and if your tank has crud settled out in it your fuel filter may need changing more frequently.
    I...
  13. Thread: Membrane snot

    by WMF
    Replies
    9
    Views
    2,708

    Trust me, no fluid exudes through the fiberglass...

    Trust me, no fluid exudes through the fiberglass outer wrap of a membrane. All fluid goes in one end and comes out the other minus the permeate.
    If a membrane is in a standard housing and there is a...
  14. Thread: Membrane snot

    by WMF
    Replies
    9
    Views
    2,708

    The real problem is the space between the...

    The real problem is the space between the membrane and wall of pressure vessel is a dead space if brine seal is in place and sealing.
    Commercial units with real recirculation use the gap between the...
  15. Thread: oil gun problem

    by WMF
    Replies
    10
    Views
    2,684

    I would start by getting wiring diagram of the...

    I would start by getting wiring diagram of the primary control that is on the burner. There are several different ones used on a 701. Find out what exactly is "burned up" on the controllers.
    If the...
  16. Replies
    253
    Views
    216,504

    If you don't have one already keep your eye out...

    If you don't have one already keep your eye out for a Genuine made in USA Beverly shear. They make cutting metal so easy and they will last forever if cared for.
  17. Replies
    253
    Views
    216,504

    Another great old USA made tool. The crimping...

    Another great old USA made tool. The crimping dies should go on the shaft before the beading dies so it makes a shoulder after the crimp. You can use just the crimping dies or just the beading dies...
  18. Replies
    253
    Views
    216,504

    Looks great, that arch will last a lifetime if...

    Looks great, that arch will last a lifetime if kept dry.
    I think the brake you may have been thinking yours was is a Cornice truss brake made in Buffalo. They made them out of a combination of wood...
  19. Replies
    253
    Views
    216,504

    Looks like a Chicago, I have an old Chicago 818...

    Looks like a Chicago, I have an old Chicago 818 and the legs and castings look exactly the same. The Chicago's have a round brass tag with a single rivet in the center located on the right side...
  20. Replies
    253
    Views
    216,504

    Sweet! Is that a 1016 ? Looks like it found a...

    Sweet! Is that a 1016 ? Looks like it found a good home.
  21. Replies
    4
    Views
    1,337

    Changed bearings on one a few years ago. The...

    Changed bearings on one a few years ago.
    The impeller unsrews from shaft then you can remove motor.
    Make sure to index everything. I would draw a witness line down one side of pump/motor with paint...
  22. Thread: Releaser problems

    by WMF
    Replies
    18
    Views
    5,815

    I drilled and tapped a 6-32 screw into the thick...

    I drilled and tapped a 6-32 screw into the thick clear plastic bar that the bushings go through. Used a screw just long enough to pin bushing,
    do this at your own risk as these plastic parts are not...
  23. Thread: Releaser problems

    by WMF
    Replies
    18
    Views
    5,815

    I have two double vertical Bernards. Both have...

    I have two double vertical Bernards. Both have had issues of which you speak and the cause was the white machined bushings in the clear
    cover that the float rods run through.
    The bushings are press...
  24. Replies
    3
    Views
    1,678

    My Sihi 3708 is stuck every year even though it...

    My Sihi 3708 is stuck every year even though it is stored with glycol. I panicked the first time it happened then sat back and analyzed why it is stuck.
    The rotors and housings are close tolerance...
  25. What size burner tube does your 301 have? This...

    What size burner tube does your 301 have? This burner can be ordered with either a 3.25" tube for 3 to 6 gph firing rate or 3.5" burner tube for 4 to 7 gph.
    Your firing rate is right at the cutoff...
Results 1 to 25 of 190
Page 1 of 8 1 2 3 4