Search:

Type: Posts; User: mol1jb

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    9
    Views
    797

    Easiest would be to just extend the 3/16 runs,...

    Easiest would be to just extend the 3/16 runs, especially with significant drop. I do consolidate my 3/16 into 3/4 mainline but only because the slope at the end of my runs is too low for 3/16 to...
  2. Replies
    6
    Views
    275

    I can't remember where I heard it but I want to...

    I can't remember where I heard it but I want to say that firebricks are more durable than refractory cement. I think this is why most arch manufacturers say to make the joints between the bricks as...
  3. Thread: Maple popcorn

    by mol1jb
    Replies
    3
    Views
    475

    As an experienced popcorn consumer I would not...

    As an experienced popcorn consumer I would not make it until the morning of. Even saving popcorn for a half a day it can taste a bit stale. You could experiment with containers that seal well and see...
  4. Based on what you described I would look at a...

    Based on what you described I would look at a 2x6. That would keep your boil time around 3-4 hours a day, depending on how much sap you collect and how hard you run the evap. It would also be able to...
  5. I assume you are going from a 2x4 flat pan to...

    I assume you are going from a 2x4 flat pan to flue pan setup? What are your max taps? I'm sure you did but I'll say it anyways, that it is always good to think of the future if you have options to...
  6. Replies
    10
    Views
    1,454

    Your answer will depend on what you have to build...

    Your answer will depend on what you have to build with or attach to. For my elevated tanks, I have 2x elevated platforms built. Both are built like mini decks. On the building side there is a ledger...
  7. Replies
    18
    Views
    1,948

    That is coming along nicely!

    That is coming along nicely!
  8. Replies
    3
    Views
    421

    Thin enough so that is is easy to work with and...

    Thin enough so that is is easy to work with and thick enough to support your brick. I was fortunate so salvage the stainless for my arch build but it was on the thick side (around 10 ga) and a pain...
  9. Thread: Getting ready

    by mol1jb
    Replies
    165
    Views
    32,937

    Sounds like you have a good handle on it. If your...

    Sounds like you have a good handle on it. If your selling, location is a key factor and I bet your new shack location will help with sales. And will all that you will be gaining with electricity,...
  10. Replies
    0
    Views
    436

    A good day in the woods

    So I finished installing a new mainline to a new section of woods today (300ft of 3/4in). That is always a good feeling because for where I am at this is the hardest part to set up new woods (hills...
  11. Thread: Getting ready

    by mol1jb
    Replies
    165
    Views
    32,937

    No option of solar at shack?

    No option of solar at shack?
  12. Replies
    25
    Views
    6,875

    Also keep an eye out for used RO's on this site...

    Also keep an eye out for used RO's on this site and Bascoms.
  13. Replies
    25
    Views
    6,875

    For 1000 taps and a 2x8 you would have to have a...

    For 1000 taps and a 2x8 you would have to have a good sized RO to not drown in sap. I would recommend to buy as big RO as you can for your money. Deer Run Maple have good economical hobby RO's for...
  14. Replies
    6
    Views
    560

    Probably the best thing I did after hearing it on...

    Probably the best thing I did after hearing it on this site was put an overflow line from the head tank back to the sap tank in case your RO fills your head tank too fast then you wont be dumping...
  15. Thread: Plumbing a tank

    by mol1jb
    Replies
    3
    Views
    531

    Any food grade pipe will work fine. For larger...

    Any food grade pipe will work fine. For larger pipe I usually use pvc. Smaller pipe I usually use a flexible pipe like mainline or similar just make sure it is rated for potable water.
  16. Replies
    8
    Views
    780

    Wow that is a lot of years of splitting wood. Not...

    Wow that is a lot of years of splitting wood. Not to mention splitting for an evaporator takes twice as long as the splits are 1/2 the size as the wood stove splits.



    12 cord! That is a lot of...
  17. Replies
    8
    Views
    780

    Its a good day...

    ...when the wood shed is full. Mine is attached to the kitchen and is large enough to fit 1.5 cord, more than years worth. Thats good cause we are growing a bit every year.
  18. Thread: DSD saddles

    by mol1jb
    Replies
    1
    Views
    328

    Many including my self like these very much.

    Many including my self like these very much.
  19. Replies
    148
    Views
    50,123

    Would 3/4 inch be large enough for the manifold?...

    Would 3/4 inch be large enough for the manifold? I would like to do 1/2 inch branches. Larger than 3/4 makes fittings expensive.
  20. I would buy the pan first and do some...

    I would buy the pan first and do some modification to your block arch. That is what my dad did this past season. He took his block arch and did away with his 2 steam table pans, bought a 2x3 pan and...
  21. Like anything, it depends. If you are running RO...

    Like anything, it depends. If you are running RO then you can get a smaller evap and be fine (2x3 or 2x4). Depending on your budget, you could buy new pan and arch or with a tighter budget buy a used...
  22. Replies
    9
    Views
    717

    Depending on what your running some just use a...

    Depending on what your running some just use a temp switch. That keeps things simple
  23. Replies
    1
    Views
    352

    Mad procon pressure?

    Hey all,

    I see on the procon spec sheet they are rated up to 250psi. Is that the max pressure you can get out of a procon pump? Looking at a series 5.
  24. Replies
    148
    Views
    50,123

    Thanks for the info

    Thanks for the info
  25. Replies
    148
    Views
    50,123

    What do you think about making the manifold out...

    What do you think about making the manifold out of pvc and the take offs copper. That would help keep the cost down and make it easier to build for someone like me with no soldering experience
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4