+ Post New Thread
Page 21 of 163 FirstFirst ... 1112131415161718192021222324252627282930314171121 ... LastLast
Threads 401 to 420 of 3245

Forum: Tubing Installation and Tapping of Tubing Systems

Discussion about tubing installation and techniques of tapping them

  1. Tubing Installation Pace

    Started by MiMappleMan‎, 01-26-2020 11:12 PM
    • Replies: 7
    • Views: 3,785
    iby
    01-27-2020, 12:18 PM Go to last post

  2. Need Some Guidance

    Started by HondoLane‎, 01-22-2020 08:40 PM
    • Replies: 7
    • Views: 2,857
    HondoLane
    01-26-2020, 01:19 PM Go to last post

  3. Recommendations needed 5/16" or 3/4"

    Started by Maple River Sugar‎, 12-30-2019 11:14 PM
    • Replies: 7
    • Views: 2,083
    Maple River Sugar
    01-26-2020, 11:58 AM Go to last post

  4. Compressed air cans

    Started by MapleCamp‎, 01-25-2020 04:36 PM
    • Replies: 4
    • Views: 1,454
    johnallin
    01-26-2020, 10:35 AM Go to last post

  5. Shurflo

    Started by toothfairy050‎, 01-25-2020 05:14 PM
    • Replies: 1
    • Views: 993
    mol1jb
    01-25-2020, 05:19 PM Go to last post

  6. Tapping Bits

    Started by Maple Hill‎, 01-22-2020 07:03 PM
    • Replies: 5
    • Views: 2,187
    Maple Hill
    01-25-2020, 02:11 PM Go to last post

  7. Tubing Condition and Advice for Installations Taken Down After the Season

    Started by Ghs57‎, 01-20-2020 09:22 AM
    2 Pages •
    1 2
    1 Attachment(s)
    • Replies: 14
    • Views: 4,286
    Sugarmaker
    01-24-2020, 10:29 AM Go to last post

  8. A Few 3/16 Questions

    Started by Kubota‎, 01-22-2020 07:55 AM
    2 Pages •
    1 2
    1 Attachment(s)
    • Replies: 11
    • Views: 4,432
    Pdiamond
    01-22-2020, 08:15 PM Go to last post

  9. Holding up lines with a small nail - Bad Idea

    Started by bryankloos‎, 01-22-2020 12:47 PM
    • Replies: 5
    • Views: 2,826
    Sugarmaker
    01-22-2020, 04:46 PM Go to last post

  10. 3 Laterals to One Spot in Mainline

    Started by SeanD‎, 01-20-2020 06:57 PM
    • Replies: 7
    • Views: 3,282
    maple flats
    01-22-2020, 10:09 AM Go to last post

  11. Valves for Isolating Leaks on 3/16

    Started by kboone1‎, 01-21-2020 12:37 PM
    1 Attachment(s)
    • Replies: 9
    • Views: 1,965
    White Crow
    01-21-2020, 09:55 PM Go to last post

  12. Sapling taps

    Started by Woody77‎, 01-19-2020 12:02 PM
    • Replies: 4
    • Views: 1,700
    DrTimPerkins
    01-21-2020, 08:09 AM Go to last post

  13. New Mainline in Warm Weather

    Started by SeanD‎, 01-08-2020 05:13 PM
    2 Pages •
    1 2
    • Replies: 13
    • Views: 3,434
    VT_K9
    01-20-2020, 09:02 PM Go to last post

  14. should I change to 5/16

    Started by White Crow‎, 01-18-2020 07:45 AM
    2 Pages •
    1 2
    • Replies: 10
    • Views: 3,108
    White Crow
    01-20-2020, 11:10 AM Go to last post

  15. Stretching mainline

    Started by calvertbrothers‎, 01-09-2020 08:12 PM
    • Replies: 6
    • Views: 2,701
    VT_K9
    01-19-2020, 09:35 PM Go to last post

  16. End of line

    Started by Trapper2‎, 01-09-2020 07:55 PM
    2 Pages •
    1 2
    • Replies: 12
    • Views: 3,425
    Trapper2
    01-11-2020, 09:17 PM Go to last post

  17. Most Productive Setup for Shurflo Vac

    Started by kboone1‎, 01-10-2020 09:05 AM
    2 Attachment(s)
    • Replies: 5
    • Views: 2,295
    Super Sapper
    01-11-2020, 06:16 AM Go to last post

  18. Measuring Slope

    Started by bryankloos‎, 01-02-2020 09:20 PM
    • Replies: 9
    • Views: 4,606
    mol1jb
    01-10-2020, 07:16 PM Go to last post

  19. Early tapping

    Started by steve J‎, 12-22-2019 05:49 PM
    2 Pages •
    1 2
    • Replies: 15
    • Views: 6,210
    Sugar Bear
    01-10-2020, 11:27 AM Go to last post

  20. Using cv spouts on drops to buckets

    Started by Pdiamond‎, 12-13-2019 12:16 AM
    2 Pages •
    1 2
    • Replies: 10
    • Views: 5,120
    Sugar Bear
    01-09-2020, 07:07 PM Go to last post
+ Post New Thread
Page 21 of 163 FirstFirst ... 1112131415161718192021222324252627282930314171121 ... LastLast

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts

Forum Rules