PDA

View Full Version : ro build



Shon
04-13-2020, 12:26 PM
would a 1/2hp myers high pressure pump be big enough to run in a 2x 4x40 system thanks i have chance to get a fair price on the pump its definately in my budget but would like to know if it be big enough before i buy it

maple flats
04-13-2020, 01:06 PM
Look up the pump curve to be sure. For good RO action you will need close to 300PSI, but lesser performance can be gotten with pressures down to about 100-120PSI. In fact 300 is only the typical pressure top end for low end R.O's, with the right housing it is not the max.

Shon
04-13-2020, 01:13 PM
i tried looking at the pump curve but i stupid with some of that stuff an couldn make sense of it.and by housing you mean the 4x40 canisters.they rated for 300 psi.im looking at building a system to take care of approx 800 taps on high vac

maple flats
04-13-2020, 01:13 PM
A pump rated to push water up to about 278' lift will be at about 120 PSI. That will not be the same for sap, because the specific gravity is different.

Shon
04-13-2020, 02:31 PM
can you have too much pump.1.5 hp say .

maple flats
04-13-2020, 04:11 PM
My 2x4x40 ro has a 2 hp motor, and it can go up to 300 psi. I don't think a 1.5 HP will give you 300 psi, but it should give you over 200 PSI which would remove at least 50% of the water in one pass from over 200 gal.

bill m
04-13-2020, 05:48 PM
If you want to get to 800 taps on high vacuum I would think you would want a system that would do at least 300 GPH, 600 would be better.

Shon
04-13-2020, 07:38 PM
My 2x4x40 ro has a 2 hp motor, and it can go up to 300 psi. I don't think a 1.5 HP will give you 300 psi, but it should give you over 200 PSI which would remove at least 50% of the water in one pass from over 200 gal.

is your system homemade or a factory set up.if i can make something that removes half my water in a pass how long in time wise from 200 gal would this take approx.i just need a starting point somewhere.this season was a killer for me.sap was 1-1.5 all season long.i can reduce about 45-50 g an hr while boiling.thank you for your help.likely im sure i will have alot more questions as i go along.pretty sure im gonna purchase the 1.5 hp pump as so far its the only deal i came across besides the 1/2 hp an that be too small.

Shon
04-13-2020, 07:40 PM
If you want to get to 800 taps on high vacuum I would think you would want a system that would do at least 300 GPH, 600 would be better.is it possible to build a ro of this size

bill m
04-14-2020, 08:09 AM
I'm sure you could build one of this size but at what cost, I don't know. I bought my 600 GPH machine from H2O. When planning your build make a complete list of everything you need. If you start buying parts and pieces as you go you may find you are spending way more then you expected. One of the things I don't see included in some of the home made units is a wash tank, a way to protect it from to high of a temperature and a heater if you are not going to let the pump create the heat as it washes.

Shon
04-14-2020, 03:06 PM
I'm sure you could build one of this size but at what cost, I don't know. I bought my 600 GPH machine from H2O. When planning your build make a complete list of everything you need. If you start buying parts and pieces as you go you may find you are spending way more then you expected. One of the things I don't see included in some of the home made units is a wash tank, a way to protect it from to high of a temperature and a heater if you are not going to let the pump create the heat as it washes.whats the purpose of the wash tank.when i look at smaller units i see the option just wondering the purpose as they come with or without.i also wondering about the idea of adding a recirculating pump and what size pump required ,does it need to be more sized or less sized then the high pressure pump

bill m
04-14-2020, 08:23 PM
When you do a wash on the membrane you need to mix the soap with permeate to reach a ph level of about 11.5 Then that solution circulates through the membrane till it reaches about 104 degrees. You then drain the membrane and do a rinse with just permeate.

maple flats
04-14-2020, 08:35 PM
Those who order an RO without a wash tank, use a suitable tank or bucket of their own.